Remove & Uninstall Mono-a-Mono 4.2 Completely from Windows

Do you have trouble in completely uninstalling Mono-a-Mono 4.2 from your system? Are you looking for an effective solution to thoroughly get rid of it off the computer? Do not worry! You came to the right place, and you will be able to uninstall Mono-a-Mono 4.2 without any difficulty.

Mono-a-Mono 4.2 Mono-a-Mono 4.2 Gets rid of hiss and clicks on stereo recordings of old records and tapes.

Mono-a-Mono removes scratches and tape or surface noise from stereo recordings of mono sources. It can be used to enhance digital recordings of old records (whether 78, 45, or 33 rpm, shellac, acetate or vinyl), audio tapes (reel-to-reel or cassette), or even cylinder recordings, provided only that the playback and digitisation of the signal has been performed in stereo, but the original source was mono. It rarely needs any configuration or tweaking. It produces excellent results automatically. Mono-a-Mono uses a simple muting algorithm to remove the most obvious clicks, and then filters out any components which are not present in both left and right channels. In this way, almost all the audible surface noise can be removed, and there are very few cases where any audible artefacts are introduced. Although designed to process any stereo recording of a mono source, Mono-a-Mono has some features which are especially well-suited to processing old records such as 78 rpm discs and cylinders: it allows bass and treble frequencies to be boosted or cut (to compensate for the different equalisation characteristics used during the recording process) and it has a "click removal" function to reduce the effect of the worst scratches and clicks from old recordings. Two further sliders control simple filters to remove low-frequency rumble/hum and high-frequency hiss. The "Click Remover" slider controls the sensitivity of the click suppression algorithm, while the "Silence Enhancer" controls the suppression of quiet signals. It makes those sections of a recording quieter (the way they were meant to be). The "Rejuvenator" performs a similar function for the louder sections, reducing the audibility of any wear-and-tear (or other distortion). Mono-a-Mono is a very cost-effective method for hiding defects in old records. The default settings are usually good, but the various modules can be controlled independently to cope with even the most difficult recordings.

Gets rid of hiss and clicks on stereo recordings of old records and tapes.

However, many users have difficulties and problems away from the computer. Below we have listed possible problems when uninstalling Mono-a-Mono 4.2. If you also have this problem, you can find a useful solution for this.

It seems that there are many users who have difficulty in uninstalling software like Mono-a-Mono 4.2 from the system. And some of them get into trouble when uninstalling the software, and some of them can uninstall the software, but to get problems after removal. Some possible problems that people run into:

  • Mono-a-Mono 4.2 does not work as good as you thought.
  • Mono-a-Mono 4.2 can not be uninstalled
  • Mono-a-Mono 4.2 can not be completely uninstall and removed
  • Mono-a-Mono 4.2 or other similar software can not be installed or updated again on the computer
  • The computer system runs much slower after Mono-a-Mono 4.2 is uninstalled

Causes of the above problems :

  • Mono-a-Mono 4.2 does not appear in the program list of Add/Remove Programs
  • The uninstaller of Mono-a-Mono 4.2 can not completely remove all associated files
  • There is some software that is not compatible with Mono-a-Mono 4.2
  • There are many remnants left in the registry and hard drive
  • The .dll, .sys or other files shared with other software are deleted

Manually Uninstall Mono-a-Mono 4.2 with Windows Add/Remove Programs.

Windows "Add/Remove Programs" offers users a way to uninstall the program, and each Operating system has a "Add/Remove programs" function.

  • Click "Start menu" and run "Control Panel".
  • Locate Mono-a-Mono 4.2 (or Steve Beet) and click "Change/Remove" to uninstall the program.
  • Follow the uninstall wizard and uninstall the program.
Uninstall Mono-a-Mono 4.2
Manually Uninstall Mono-a-Mono 4.2 with Build-in Uninstaller.

Most computer programs are installed with its build-in uninstaller that can also help uninstall the program.

  • Click Start menu and move your mouse to All Programs.
  • Find Search Mono-a-Mono 4.2 folder and click on its Uninstaller.
  • Follow its uninstaller and uninstall the program.

To run its uninstaller, you can also

  • Go to the folder where the program is installed.
  • Locate its uninstaller usually named as unins000.exe or uninstall.exe
  • Double click on its uninstaller and follow it to uninstall the program.

Please know that Windows "Add/Remove Programs" and its build-in uninstaller can remove only the main executable program files, but not all program files and components. Some invalid files can be left in the registry and folders. To completely uninstall Mono-a-Mono 4.2, you need to get rid of these remnants, otherwise, it will slow down your computer and block the installation of other incompatible programs.

To thoroughly delete its files, please follow the steps:

  • Run Registry Editor
  • Find and delete all registry entries of the program in HKEY_CURRENT_USER\Software\Steve Beet\, HKEY_LOCAL_MACHINE\SOFTWARE\Steve Beet\ and HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Run\
  • Find and delete all files of the program in system folders C:\Program Files\Steve Beet\, C:\Document and Settings\All Users\Application Data\Steve Beet\ and C:\Documents and Settings\%USER%\Application Data\Steve Beet\.

NOTE: We recommend only for advanced computer users, manually edit the registry and remove Mono-a-Mono because deleting any single registry error leads to a serious problem or even a system crash.